MID-SIDE MIC RECORDING BASICS
Get Maximum Control Over your Stereo Image
When most people think of stereo recording, the first thing that comes to mind is a matched pair of microphones, arranged in a XY pattern. It makes sense, of course, since that's the closest way to replicate a real pair of human ears.
But while XY microphone recording is the most obvious method, it's not the only game in town. The Mid/Side (M/S) recording technique is more complex, but it offers dramatic advantages over standard miking. If you've never heard of M/S recording, or you've been afraid to try it, you're missing out on a powerful weapon in your recording arsenal.
Mid/Side microphone recording is hardly a new concept. It was devised by EMI engineer Alan Blumlein, an early pioneer of stereophonic and surround sound. Blumlein patented the technique in 1933 and used it on some of the earliest stereophonic recordings.
The M/S microphone recording technique is used extensively in broadcast, largely because properly recorded M/S tracks are always mono-compatible. M/S is also a popular technique for studio recording, and its convenience and flexibility make it a good choice for live recording as well.
The main weakness of the XY microphone technique is the fact that you're stuck with what you've recorded — as well as its stereo image. And in some cases, collapsing those tracks to mono can result in some phase cancellation.
The M/S technique gives you more control over the width of the stereo spread than other microphone recording techniques, and allows you to make adjustments at any time after the recording is finished.
What You Need
While XY recording requires a matched pair of microphones to create a consistent image, M/S recording often uses two completely different mics, or uses similar microphones set to different pickup patterns.
The "Mid" microphone is set up facing the center of the sound source. Typically, this mic would be a cardioid or hypercardioid pattern (although some variations of the technique use an omni or figure-8 pattern). The "Side" mic must be a figure-8 pattern. This mic is aimed 90 degrees off-axis from the sound source. Both mic capsules should be placed as closely as possible, typically one above the other.
How it Works
At its most basic, the M/S recording technique is actually not all that complicated. The concept is that the Mid microphone acts as a center channel, while the Side microphone's channel creates ambience and directionality by adding or subtracting information from either side.
The Side mic's figure-8 pattern, aimed at 90 degrees from the source, picks up ambient and reverberant sound coming from the sides of the sound stage. Since it's a figure-8 pattern, the two sides are 180 degrees out of phase. In other words, a positive charge to one side of the mic's diaphragm creates an equal negative charge to the other side. The front of the mic, which represents the plus (+) side, is usually pointed to the left of the sound stage, while the rear, or minus (-) side, is pointed to the right.
How to Do It
The signal from each microphone is then recorded to its own track. However, to hear a proper stereo image when listening to the recording, the tracks need to be matrixed and decoded.
Although you have recorded only two channels of audio (the Mid and Side), the next step is to split the Side signal into two separate channels. This can be done either in your DAW software or hardware mixer by bringing the Side signal up on two channels and reversing the phase of one of them. Pan one side hard left, the other hard right. The resulting two channels represent both sides of what your figure-8 Side mic is hearing.
Now you've got three channels of recorded audio — the Mid center channel and two Side channels — which must be balanced to recreate a stereo image.
Now, if you listen to just the Mid channel, you get a mono signal. Bring up the two side channels and you'll hear a stereo spread. Here's the really cool part — the width of the stereo field can be varied by the amount of Side channel in the mix!
Why It Works
An instrument at dead center (0 degrees) creates a sound that enters the Mid microphone directly on-axis. But that same sound hits the null spot of the Side figure-8 microphone. The resulting signal is sent equally to the left and right mixer buses and speakers, resulting in a centered image. An instrument positioned 45 degrees to the left creates a sound that hits the Mid microphone and one side of the Side figure-8 microphone.
Because the front of the Side mic is facing left, the sound causes a positive polarity. That positive polarity combines with the positive polarity from the Mid mic in the left channel, resulting in an increased level on the left side of the sound field.
Meanwhile, on the right channel of the Side mic, that same signal causes an out-of-phase negative polarity. That negative polarity combines with the Mid mic in the right channel, resulting in a reduced level on the right side. An instrument positioned 45 degrees to the right creates exactly the opposite effect, increasing the signal to the right side while decreasing it to the left.
What's the Advantage?
One of the biggest advantages of M/S recording is flexibility. Since the stereo imaging is directly dependent on the amount of signal coming to the side channels, raising or lowering the ratio of Mid to Side channels will create a wider or narrower stereo field. The result is that you can change the sound of your stereo recording after it's already been recorded, something that would be impossible using the traditional XY microphone recording arrangement.
Try some experimenting with this—listen to just the Mid channel, and you'll hear a direct, monophonic signal. Now lower the level of the Mid channel while raising the two Side channels. As the Side signals increase and the Mid decreases, you'll notice the stereo image gets wider, while the center moves further away. (Removing the Mid channel completely results in a signal that's mostly ambient room sound, with very little directionality — useful for effect, but not much else.) By starting with the direct Mid sound and mixing in the Side channels, you can create just the right stereo imaging for the track.
Another great benefit of M/S miking is that it provides true mono compatibility. Since the two Side channels cancel each other out when you switch the mix to mono, only the center Mid channel remains, giving you a perfect monaural signal. And since the Side channels also contain much of the room ambience, collapsing the mix to mono eliminates that sound, resulting in a more direct mix with increased clarity.
While most M/S recording is done with a cardioid mic for the Mid channel, varying the Mid mic can create some interesting effects. Try an omni mic pattern on the Mid channel for dramatically increased spaciousness and an extended low frequency response.
Experimenting with different combinations of mics can also make a difference. For the most part, both mics should be fairly similar in sound. This is particularly true when the sound source is large, like a piano or choir, because the channels are sharing panning information; otherwise the tone quality will vary across the stereo field. For smaller sources with a narrower stereo field, like an acoustic guitar, it's easier to experiment with mismatched mics. For example, try a brighter sounding side mic to color the stereo image and make it more spacious.
As you can see, there's a lot more to the M/S microphone technique than meets the ear, so give it a try. You'll find it to be an incredibly useful method to attain ultimate control of the stereo field in your recordings.
Here are some drum loops made with Mid/Side microphone recording. The mics were about 5 feet in front of the kit, head height with the drummer in a small room. If you have a DAW, you can download the Mid and Side WAV files separately and set up the sum-and-difference matrix yourself.